濟南飼料機械廠
聯系人：安經理
手機：152-5313-4653
郵箱：347299818@qq.com
地址：濟南市濟北開發區
選購了一臺飼料混合機，如果不能正確使用的話，不但會縮短飼料加工設備的使用壽命，而且也會影響工作效率，導致事倍功半。
1、飼料加工設備長期作業，應固定在水泥基礎上。
Feed processing equipment, long-term operation, should be fixed in the cement foundation.
2、飼料加工設備安裝完后要檢查各部緊固件的緊固情況，若有松動須予以擰緊。
Feed processing equipment after installation to check ministries fastening fasteners, if loose shall be tightened.
3、要檢查皮帶松緊度是否合適，電動機軸和粉碎機軸是否平行，飼料加工設備的粉碎機啟動前，先用手轉動轉子，檢查一下齒爪、錘片及轉子運轉是否靈活可靠，殼內有無碰撞現象，轉子的旋向是否與機上箭頭所指方向一致，電機與粉粹機潤滑是否良好。
To check the belt tension is appropriate, whether the motor shaft and the mill shaft parallel to the former mill feed processing equipment startup, first hand rotation of the rotor, check tooth claw hammer and rotor operation is flexible and reliable, with or without shell collision phenomenon, whether the rotation of the rotor machine on the arrow in the same direction, the motor and splintered machine lubrication is good.
4、不要隨便更換飼料加工設備的皮帶輪，以防轉速過高使粉碎室產生爆炸，或轉速太低影響工作效率，飼料加工設備啟動后先空轉2-3分鐘，沒有異常現象后再投料工作。
Do not replace the pulley feed processing equipment, to prevent excessive speed so that the crushing chamber to produce an explosion, or the speed is too low affect efficiency, idling 2-3 minutes after the first feed processing equipment startup, no anomalies before feeding work.
5、工作中要隨時注意飼料加工設備的運轉情況，送料要均勻，以防阻塞悶車，不要長時間超負荷運轉。若發現有振動、雜音、軸承與機體溫度過高、向外噴料等現象，應立即停車檢查，排除故障后方可繼續工作。
Work should always pay attention to the functioning of the feed processing equipment, feed should be uniform to avoid blocking stuffy car, do not overload time. If there is vibration, noise,bearing the body temperature is too high, the outside spray material and so on, should immediately stop inspection, troubleshooting can continue working.